View CY7C63101A-QXC_4152776.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CY7C63001A CY7C63101A
Universal Serial Bus Microcontroller
1.0 Features
-- Integrated USB transceiver -- Up to 16 Schmitt trigger I/O pins with internal pull-up -- Up to eight I/O pins with LED drive capability -- Special purpose I/O mode supports optimization of photo transistor and LED in mouse application * * * * * * * * * -- Maskable Interrupts on all I/O pins 8-bit free-running timer Watchdog timer (WDT) Internal power-on reset (POR) Instant-On NowTM for Suspend and Periodic Wake-up Modes Improved output drivers to reduce EMI Operating voltage from 4.0V to 5.25 VDC Operating temperature from 0-70C Available in space saving and low-cost 20-pin PDIP, 20-pin SOIC, and 24-pin QSOP packages Industry-standard programmer support * Low-cost solution for low-speed USB peripherals such as mouse, joystick, and gamepad * USB Specification Compliance -- Conforms to USB 1.5-Mbps Specification, Version 1.1 -- Supports one device address and two endpoints (one control endpoint and one data endpoint) * 8-bit RISC microcontroller -- Harvard architecture -- 6-MHz external ceramic resonator -- 12-MHz internal operation -- USB optimized instruction set * Internal memory -- 128 bytes of RAM -- 4 Kbytes of EPROM
Logic Block Diagram
6-MHz CERAMIC RESONATOR R/CEXT
OSC
INSTANT-ON NOWTM
RAM 128-Byte
8-bit Timer
EPROM 2/4 KByte
Poweron Reset Watch Dog Timer
8-bit RISC core USB Engine PORT 0 PORT 1
Interrupt Controller
D+,D- VCC/VSS
P0.0-P0.7
P1.0-P1.7
Cypress Semiconductor Corporation Document #: 38-08026 Rev. *A
*
3901 North First Street
*
San Jose, CA 95134 * 408-943-2600 Revised October 5, 2004
CY7C63001A CY7C63101A
2.0 Pin Configurations (Top View)
20-pin DIP/SOIC
P0.0 P0.1 P0.2 P0.3 P1.0 P1.2 VSS VPP CEXT XTALIN 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 P0.4 P0.5 P0.6 P0.7 P1.1 P1.3 D+ D- VCC XTALOUT P0.0 P0.1 P0.2 P0.3 P1.0 P1.2 P1.4 P1.6 VSS VPP CEXT XTALIN
24-pin SOIC/QSOP
1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 P0.4 P0.5 P0.6 P0.7 P1.1 P1.3 P1.5 P1.7 D+ D- VCC XTALOUT
CY7C63101A DIE
4 3 2 1 24 23 22 21 5 6 7 8 20 19 18 17
9 10 11 12 13 14 15 16
3.0
Functional Overview
The CY7C630/101A is a family of 8-bit RISC One Time Programmable (OTP) microcontrollers with a built-in 1.5-Mbps USB Serial Interface Engine (SIE). The microcontroller features 35 instructions that are optimized for USB applications. In addition, the microcontroller features 128 bytes of internal RAM and four Kbytes of program memory space. The Cypress USB Controller accepts a 6-MHz ceramic resonator as its clock source. This clock signal is doubled within the chip to provide a 12- MHz clock for the microprocessor. The microcontroller features two ports of up to sixteen general purpose I/Os (GPIOs). Each GPIO pin can be used to generate an interrupt to the microcontroller. Additionally, all
pins in Port 1 are equipped with programmable drivers strong enough to drive LEDs. The GPIO ports feature low EMI emissions as a result of controlled rise and fall times and unique output driver circuits. The Cypress microcontrollers have a range of GPIOs to fit various applications; the CY7C6300XA has twelve GPIOs and the CY7C6310XA has sixteen GPIOs. Notice that each part has eight `low-current' ports (Port 0) with the remaining ports (Port 1) being `highcurrent' ports. The 12-GPIO CY7C6300XA is available in 20-pin PDIP (-PC) and 20-pin SOIC (-SC) packages. The 26-GPIO CY7C6310XA is available in 24-pin QSOP (-QC) package.
4.0
P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 XTALIN
Pin Definitions
Name I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I O 20-Pin 1 2 3 4 20 19 18 17 5 16 6 15 - - - - 10 11 24-pin 1 2 3 4 24 23 22 21 5 20 6 19 7 18 8 17 12 13 Die Pad # 1 2 3 4 24 23 22 21 5 20 6 19 7 18 8 17 12 13 Port 0 bit 0 Port 0 bit 1 Port 0 bit 2 Port 0 bit 3 Port 0 bit 4 Port 0 bit 5 Port 0 bit 6 Port 0 bit 7 Port 1 bit 0 Port 1 bit 1 Port 1 bit 2 Port 1 bit 3 Port 1 bit 4 Port 1 bit 5 Port 1 bit 6 Port 1 bit 7 Ceramic resonator in Ceramic resonator out Page 2 of 25 Description
XTALOUT
Document #: 38-08026 Rev. *A
CY7C63001A CY7C63101A
4.0
CEXT D+ D- VPP VCC VSS
Pin Definitions (continued)
Name I/O I/O I/O I/O - - - 20-Pin 9 14 13 8 12 7 24-pin 11 16 15 10 14 9 Die Pad # 11 16 15 10 14 9 Description Connects to external R/C timing circuit for optional `suspend' wakeup USB data+ USB data- Programming voltage supply, tie to ground during normal operation Voltage supply Ground
5.0
VCC VSS VPP XTALIN
Pin Description
Name Description One pin. Connects to the USB power source or to a nominal 5V power supply. Actual VCC range can vary between 4.0V and 5.25V. One pin. Connects to ground. One pin. Used in programming the on-chip EPROM. This pin should be tied to ground during normal operations. One pin. Input from an external ceramic resonator. One pin. Return path for the ceramic resonator (leave unconnected if driving XTALIN from an external oscillator). Sixteen pins. P0.0-P0.7 are the 8 I/O lines in Port 0. P1.0-P1.7 are the 8 I/O lines in Port 1. P1.0-P1.3 are supported in the CY7C6300XA. All I/O pins include bit-programmable pull-up resistors. However, the sink current of each pin can be programmed to one of sixteen levels. Besides functioning as GPIO lines, each pin can be programmed as an interrupt input. The interrupt is edge-triggered, with programmable polarity. Two pins. Bidirectional USB data lines. An external pull-up resistor must be connected between the D pin and VCC to select low-speed USB operation. One pin. Open-drain output with Schmitt trigger input. The input is connected to a rising edge-triggered interrupt. CEXT may be connected to an external RC to generate a wake-up from Suspend mode. See Section 6.4.
XTALOUT P0.0-P0.7, P1.0-P1.7
D+, D- CEXT
6.0
Functional Description
6.1.1
Program Memory Organization
The Cypress CY7C630/101A USB microcontrollers are optimized for human-interface computer peripherals such as a mouse, joystick, and gamepad. These USB microcontrollers conform to the low-speed (1.5 Mbps) requirements of the USB Specification version 1.1. Each microcontroller is a selfcontained unit with: a USB interface engine, USB transceivers, an 8-bit RISC microcontroller, a clock oscillator, timers, and program memory. Each microcontroller supports one USB device address and two endpoints. The 6-MHz clock is doubled to 12 MHz to drive the microcontroller. A RISC architecture with 35 instructions provides the best balance between performance and product cost.
The CY7C63001A and CY7C63101A each offer 4 Kbytes of EPROM. The program memory space is divided into two functional groups: interrupt vectors and program code. The interrupt vectors occupy the first 16 bytes of the program space. Each vector is 2 bytes long. After a reset, the Program Counter points to location zero of the program space. Figure 6-1 shows the organization of the Program Memory Space. 6.1.2 Security Fuse Bit
The Cypress USB microcontroller includes a security fuse bit. When the security fuse is programmed, the EPROM program memory outputs 0xFF to the EPROM programmer, thus protecting the user's code.
6.1
Memory Organization
The memory in the USB Controller is organized into user program memory in EPROM space and data memory in SRAM space.
Document #: 38-08026 Rev. *A
Page 3 of 25
CY7C63001A CY7C63101A
after reset PC Address 0x0000 0x0002 0x0004 0x0006 0x0008 0x000A 0x000C 0x000E 0x0010 Reset Vector Interrupt Vector - 128 s Interrupt Vector - 1.024 ms Interrupt Vector - USB Endpoint 0 Interrupt Vector - USB Endpoint 1 Reserved Interrupt Vector - GPIO Interrupt Vector - Cext On-chip program Memory
0x07FF
2K ROM (CY7C63000A, CY7C63100A)
0x0FFF
4K ROM (CY7C63001A, CY7C63101A)
Figure 6-1. Program Memory Space 6.1.3 Data Memory Organization The DSP pre-decrements by one whenever a PUSH instruction is executed and it increments by one after a POP instruction is used. The default value of the DSP after reset is 0x00, which would cause the first PUSH to write into USB FIFO space for Endpoint 1. Therefore, the DSP should be mapped to a location such as 0x70 before initiating any data stack operations. Refer to the Reset section for more information about DSP remapping after reset. Figure 6-2 illustrates the Data Memory Space.
The USB Controller includes 128 bytes of data RAM. The upper 16 bytes of the data memory are used as USB FIFOs for Endpoint 0 and Endpoint 1. Each endpoint is associated with an 8-byte FIFO. The USB controller includes two pointers into data RAM, the Program Stack Pointer (PSP) and the Data Stack Pointer (DSP). The value of PSP after reset is 0x00. The PSP increments by two whenever a CALL instruction is executed and it decrements by two whenever a RET instruction is used.
Document #: 38-08026 Rev. *A
Page 4 of 25
CY7C63001A CY7C63101A
after reset DSP PSP Address 0x00 0x02 0x04
user firmware
DSP
0x70
USB FIFO - Endpoint 0
0x77 0x78 USB FIFO - Endpoint 1
0x7F Figure 6-2. Data Memory Space
6.2
I/O Register Summary
I/O registers are accessed via the I/O Read (IORD) and I/O Write (IOWR, IOWX) instructions. Table 6-1. I/O Register Summary Register Name P0 Data P1 Data P0 IE P1 IE P0 Pull-up P1 Pull-up EP0 TX Config. EP1 TX Config. USB DA USB SCR EP0 RX Status GIE WDT Cext Timer P0 Isink I/O Address 0x00 0x01 0x04 0x05 0x08 0x09 0x10 0x11 0x12 0x13 0x14 0x20 0x21 0x22 0x23 0x30-0x37 Read/Write R/W R/W W W W W R/W R/W R/W R/W R/W R/W W R/W R W Function General purpose I/O Port (low current) General purpose I/O Port (high current) Interrupt enable for Port 0 pins Interrupt enable for Port 1 pins Pull-up resistor control for Port 0 pins Pull-up resistor control for Port 1 pins USB Endpoint 0 transmit configuration USB Endpoint 1 transmit configuration USB device address USB status and control USB Endpoint 0 receive status Global Interrupt Enable Watchdog Timer clear External R-C Timing circuit control Free-running timer Page Figure 6-8 Figure 6-9 Figure 6-17 Figure 6-18 Figure 6-11 Figure 6-12 Figure 6-22 Figure 6-23 Figure 6-20 Figure 6-24 Figure 6-21 Figure 6-15 Figure 6-4 Figure 6-5 Figure 6-6
Input sink current control for Port 0 pins. There is one Figure 6-13 Isink register for each pin. Address of the Isink register for pin 0 is located at 0x30 and the register address for pin 7 is located at 0x37.
Document #: 38-08026 Rev. *A
Page 5 of 25
CY7C63001A CY7C63101A
Table 6-1. I/O Register Summary (continued) Register Name P1 Isink I/O Address 0x38-0x3F Read/Write W Function Page Input sink current control for Port 1 pins. There is one Figure 6-13 Isink register for each pin. Address of the Isink register for pin 0 is located at 0x38 and the register address for pin 7 is located at 0x3F. The number of Port 1 pins depends on package type. Processor status and control register Figure 6-3
SCR
0xFF
R/W
6.3
Reset
The USB Controller supports three types of resets. All registers are restored to theirWatchdog default states during a reset. The USB Device Address is set to 0 and all interrupts are disabled. In addition, the Program Stack Pointer (PSP) is set to 0x00 and the Data Stack Pointer (DSP) is set to 0x00. The user should set the DSP to a location such as 0x70 to reserve 16 bytes of USB FIFO space. The assembly instructions to do so are: MOV A, 70h ; Move 70 hex into Accumulator, use 70 instead of 6F because the dsp is ; always decremented by 1 before the data transfer of the PUSH instruction occurs SWAP A, DSP ; Move Accumulator value into dsp The three reset types are: 1. Power-On Reset (POR) 2. Watchdog Reset (WDR) 3. USB Reset
The occurrence of a reset is recorded in the Status and Control Register located at I/O address 0xFF (Figure 6-3). Reading and writing this register are supported by the IORD and IOWR instructions. Bits 1, 2, and 7 are reserved and must be written as zeros during a write. During a read, reserved bit positions should be ignored. Bits 4, 5, and 6 are used to record the occurrence of POR, USB, and WDR Reset respectively. The firmware can interrogate these bits to determine the cause of a reset. If a Watchdog Reset occurs, firmware must clear the WDR bit (bit 6) in the Status and Control Register to re-enable the USB transmitter (please refer to the Watchdog Reset section for further details). Bit 0, the "Run" control, is set to 1 at POR. Clearing this bit stops the microcontroller (firmware normally should not clear this bit). Once this bit is set to LOW, only a reset can set this bit HIGH. The microcontroller resumes execution from ROM address 0x00 after a reset unless the Suspend bit (bit 3) of the Status and Control Register is set. Setting the Suspend bit stops the clock oscillator and the interrupt timers and powers down the microcontroller. The detection of any USB activity, the occurrence of a GPIO Interrupt, or the occurrence of the Cext Interrupt terminates the suspend condition.
b7 Reserved
b6 WDR R/W
b5 USBR R/W 0
b4 POR R/W 1
b3 SUSPEND R/W 0
b2 Reserved
b1 Reserved
b0 RUN R/W
0
0
0
0
1
Figure 6-3. Status and Control Register (SCR - Address 0xFF) 6.3.1 Power-On Reset suspended mode at the end of POR to conserve power (the clock oscillator, the timers, and the interrupt logic are turned off in suspend mode). After POR, only a non-idle USB Bus state terminates the suspend mode. The microcontroller then begins execution from ROM address 0x00.
Power-On Reset (POR) occurs every time the power to the device is switched on. Bit 4 of the Status and Control Register is set to record this event (the register contents are set to 00011001 by the POR). The USB Controller is placed in
Document #: 38-08026 Rev. *A
Page 6 of 25
CY7C63001A CY7C63101A
7.168 to 8.192 ms 8.192 ms
Last write to Watchdog Timer Register
No write to WDT register, so WDR goes HIGH
Figure 6-4. Watchdog Reset
Execution begins at Reset Vector 0x00
6.3.2
Watchdog Reset (WDR)
The Watchdog Timer Reset (WDR) occurs when the Most Significant Bit of the 4-bit Watchdog Timer Register transitions from LOW to HIGH. Writing any value to the write-only Watchdog Restart Register at 0x21 clears the timer (firmware should periodically write to the Watchdog Restart Register in the `main loop' of firmware). The Watchdog timer is clocked by a 1.024-ms clock from the free-running timer. If 8 clocks occur between writes to the timer, a WDR occurs and bit 6 of the Status and Control Register is set to record the event. A Watchdog Timer Reset lasts for 8.192 ms, at which time the microcontroller begins execution at ROM address 0x00. The USB transmitter is disabled by a Watchdog Reset because the USB Device Address Register is cleared (otherwise, the USB Controller would respond to all address 0 transactions). The transmitter remains disabled until the WDR bit (bit 6) in the Status and Control Register is reset to 0 by firmware. 6.3.3 USB Bus Reset
register. All logic blocks in the device are turned off except the USB receiver, the GPIO interrupt logic, and the Cext interrupt logic. The clock oscillator and the free-running and Watchdog timers are shut down. The suspend mode is terminated when one of the following three conditions occur: 1. USB activity 2. A GPIO interrupt 3. Cext interrupt The clock oscillator, GPIO, and timers restart immediately upon exiting suspend mode. The USB engine and microcontroller return to a fully functional state no more than 256 s later. Before servicing any interrupt requests, the microcontroller executes the instruction following the I/O write that placed the device into suspend mode. Both the GPIO interrupt and the Cext interrupt allow the USB Controller to wake-up periodically and poll potentiometers, optics, and other system components while maintaining a very low average power consumption. The Cext Interrupt is preferred for lowest power consumption. For Cext to generate an "Instant-on" interrupt, the pin must be connected to ground with an external capacitor and connected to VCC with an external resistor. A "0" is written to the Cext register located at I/O address 0x22 to discharge the capacitor. Then, a "1" is written to disable the open-drain output driver. A Schmitt trigger input circuit monitors the input and generates a wake-up interrupt when the input voltage rises above the input threshold. By changing the values of the external resistor and capacitor, the user can fine tune the charge rate of the RC timing circuit. The format of the Cext register is shown in Figure 6-5. Reading the register returns the value of the Cext pin. During a reset, the Cext pin is HIGH. b3 Reserved 0 b2 Reserved 0 b1 Reserved 0 b0 CEXT R/W 1
The USB Controller recognizes a USB Reset when a Single Ended Zero (SE0) condition persists for at least 8-16 s (the Reset may be recognized for an SE0 as short as 8 s, but it is always recognized for an SE0 longer than 16 s). SE0 is the condition in which both the D+ line and the D- line are LOW. Bit 5 of the Status and Control Register is set to record this event. If the USB reset happens while the device is suspended, the suspend condition is cleared and the clock oscillator is restarted. However, the microcontroller is not released until the USB reset is removed.
6.4
Instant-on Feature (Suspend Mode)
The USB Controller can be placed in a low-power state by setting the Suspend bit (bit 3) of the Status and Control b7 Reserved 0 b6 Reserved 0 b5 Reserved 0 b4 Reserved 0
Figure 6-5. The Cext Register (Address 0x22)
Document #: 38-08026 Rev. *A
Page 7 of 25
CY7C63001A CY7C63101A
6.5 On-Chip Timer
mode is entered. Figure 6-6 illustrates the format of this register and Figure 6-7 is its block diagram. With a 6 MHz resonator, the timer resolution is 1 s. The timer generates two interrupts: the 128-s interrupt and the 1.024-ms interrupt.
The USB Controller is equipped with a free-running timer driven by a clock one-sixth the resonator frequency. Bits 0 through 7 of the counter are readable from the read-only Timer Register located at I/O address 0x23. The Timer Register is cleared during a Power-On Reset and whenever Suspend
Figure 6-6. Timer Register (Address 0x23) b7 T.7 R 0 b6 T.6 R 0 b5 T.5 R 0 b4 T.4 R 0 b3 T.3 R 0 b2 T.2 R 0 b1 T.1 R 0 b0 T.0 R 0
1.024-ms interrupt 128-ms interrupt
9
8
7
6
5
4
3
2
1
0
Resonator Clock/6
8 To Timer Register
Figure 6-7. Timer Block Diagram
6.6
General Purpose I/O Ports
Interface with peripherals is conducted via as many as 16 GPIO signals. These signals are divided into two ports: Port 0 and Port 1. Port 0 contains eight lines (P0.0-P0.7) and Port 1 contains up to eight lines (P1.0-P1.7). The number of external I/O pins depends on the package type. Both ports can be accessed by the IORD, IOWR, and IOWX instructions. The b7 P0.7 R/W 1 b6 P0.6 R/W 1 b5 P0.5 R/W 1 b4 P0.4 R/W 1
Port 0 data register is located at I/O address 0x00 while the Port 1 data register is located at I/O address 0x01. The contents of both registers are set HIGH during a reset. Refer to Figures 6-8 and 6-9 for the formats of the data registers. In addition to supporting general input/output functions, each I/O line can trigger an interrupt to the microcontroller. Please refer to the interrupt section for more details. b3 P0.3 R/W 1 b2 P0.2 R/W 1 b1 P0.1 R/W 1 b0 P0.0 R/W 1
Figure 6-8. Port 0 Data Register (Address 0x00) b7 P1.7 R/W 1 b6 P1.6 R/W 1 b5 P1.5 R/W 1 b4 P1.4 R/W 1 b3 P1.3 R/W 1 b2 P1.2 R/W 1 b1 P1.1 R/W 1 b0 P1.0 R/W 1
Figure 6-9. Port 1 Data Register (Address 0x01)
Document #: 38-08026 Rev. *A
Page 8 of 25
CY7C63001A CY7C63101A
Each GPIO line includes an internal Rup resistor. This resistor provides both the pull-up function and slew control. Two factors govern the enabling and disabling of each resistor: the state of its associated Port Pull-up register bit and the state of the Data Register bit. NOTE: The control bits in the Port Pullup register are active LOW. A GPIO line is HIGH when a "1" is written to the Data Register and a "0" is written to the respective Port Pull-up register. Writing a "0" to the port Data Register disables the port's Pullup resistor and outputs a LOW on the GPIO line regardless of the setting in the Port Pull-up Register. The output goes to a high-Z state if the Data Register bit and the Port Pull-up Register bit are both "1". Figure 6-10 illustrates the block diagram of one I/O line. The Port Isink Register is used to control the output current level and it is described later in this section. NOTE: The Isink logic block is turned off during suspend mode (please refer to the Instant-on Feature section for more details). Therefore, to prevent higher ICC currents during USB suspend mode, firmware must set ALL Port 0 and Port 1 Data Register bits (which are not externally driven to a known state), including those that are not bonded out on a particular package, to "1" and all Port 0 and Port 1 Pull-Up Register data bits to "0" to enable port pull-ups before setting the Suspend bit (bit 3 of the Status and Control Register). Table 6-2 is the Output Control truth table. VCC Port Pull-Up Register Port Data Register Rup
Port Isink Register Suspend Bit
GPIO Pin Isink DAC Disable Schmitt Trigger
Data Bus Figure 6-10. Block Diagram of an I/O Line Table 6-2. Output Control Truth Table Data Register 0 0 1 1 Port Pull-up Register 0 1 0 1 Output at I/O Pin Sink Current (`0') Sink Current (`0') Pull-up Resistor (`1') Hi-Z Interrupt Polarity High to Low Low to High High to Low Low to High
To configure a GPIO pin as an input, a "1" should be written to the Port Data Register bit associated with that pin to disable the pull-down function of the Isink DAC (see Figure 610).When the Port Data Register is read, the bit value is a "1" if the voltage on the pin is greater than the Schmitt trigger threshold, or "0" if it is below the threshold. In applications where an internal pull-up is required, the Rup pull-up resistor can be engaged by writing a "0" to the appropriate bit in the Port Pull-up Register. b7 PULL0.7 W 0 b6 PULL0.6 W 0 b5 PULL0.5 W 0 b4 PULL0.4 W 0
Both Port 0 and Port 1 Pull-up Registers are write only (see Figures 6-11 and 6-12). The Port 0 Pull-up Register is located at I/O address 0x08 and Port 1 Pull-up Register is mapped to address 0x09. The contents of the Port Pull-up Registers are cleared during reset, allowing the outputs to be controlled by the state of the Data Registers. The Port Pull-up Registers also select the polarity of transition that generates a GPIO interrupt. A "0" selects a HIGH to LOW transition while a "1" selects a LOW to HIGH transition. b3 PULL0.3 W 0 b2 PULL0.2 W 0 b1 PULL0.1 W 0 b0 PULL0.0 W 0
Figure 6-11. Port 0 Pull-up Register (Address 0x08)
Document #: 38-08026 Rev. *A
Page 9 of 25
CY7C63001A CY7C63101A
b7 PULL1.7 W 0x b6 PULL1.6 W 0 b5 PULL1.5 W 0 b4 PULL1.4 W 0 b3 PULL1.3 W 0 b2 PULL1.2 W 0 b1 PULL1.1 W 0 b0 PULL1.0 W 0
Figure 6-12. Port 1 Pull-up Register (Address 0x09) Writing a "0" to the Data Register drives the output LOW. Instead of providing a fixed output drive, the USB Controller allows the user to select an output sink current level for each I/O pin. The sink current of each output is controlled by a b7 Reserved W x b6 Reserved W x b5 Reserved W x b4 UNUSED W x dedicated Port Isink Register. The lower four bits of this register contain a code selecting one of sixteen sink current levels. The upper four bits of the register are ignored. The format of the Port Isink Register is shown in Figure 6-13. b3 ISINK3 W x b2 ISINK2 W x b1 ISINK1 W x b0 ISINK0 W x
Figure 6-13. Port Isink Register for One GPIO Line Port 0 is a low-current port suitable for connecting photo transistors. Port 1 is a high current port capable of driving LEDs. See section 8.0 for current ranges. 0000 is the lowest drive strength. 1111 is the highest. The write-only sink current control registers for Port 0 outputs are assigned from I/O address 0x30 to 0x37 with the control bits for P00 starting at 0x30. Port 1 sink current control registers are assigned from I/O address 0x38 to 0x3F with the control bits for P10 starting at 0x38. All sink current control registers are cleared during a reset, resulting in the minimum current sink setting.
6.7
XTALIN/XTALOUT
The XTALIN and XTALOUT pins support connection of a 6MHz ceramic resonator. The feedback capacitors and bias resistor are internal to the IC, as shown in Figure 6-14 Leave XTALOUT unconnected when driving XTALIN from an external oscillator. XTALOUT
clk1x (to USB SIE) clk2x (to Microcontroller) Clock Doubler 30 pF 30 pF XTALIN
Figure 6-14. Clock Oscillator On-chip Circuit
6.8
Interrupts
Interrupts are generated by the General Purpose I/O lines, the Cext pin, the internal timer, and the USB engine. All interrupts are maskable by the Global Interrupt Enable Register. Access to this register is accomplished via IORD, IOWR, and IOWX b7 CEXTIE R/W 0 b6 GPIOIE R/W 0 0 b5 Reserved b4 EP1IE R/W 0
instructions to address 0x20. Writing a "1" to a bit position enables the interrupt associated with that position. During a reset, the contents of the Interrupt Enable Register are cleared, disabling all interrupts. Figure 6-15 illustrates the format of the Global Interrupt Enable Register. b3 EP0IE R/W 0 b2 1024IE R/W 0 b1 128IE R/W 0 0 b0 Reserved
Figure 6-15. Global Interrupt Enable Register (GIER - Address 0x20) The interrupt controller contains a separate latch for each interrupt. See Figure 6-16 for the logic block diagram for the interrupt controller. When an interrupt is generated, it is latched as a pending interrupt. It stays as a pending interrupt until it is serviced or a reset occurs. A pending interrupt only Document #: 38-08026 Rev. *A generates an interrupt request if it is enabled in the Global Interrupt Enable Register. The highest priority interrupt request is serviced following the execution of the current instruction.
Page 10 of 25
CY7C63001A CY7C63101A
When servicing an interrupt, the hardware first disables all interrupts by clearing the Global Interrupt Enable Register. Next, the interrupt latch of the current interrupt is cleared. This is followed by a CALL instruction to the ROM address associated with the interrupt being serviced (i.e., the interrupt vector). The instruction in the interrupt table is typically a JMP instruction to the address of the Interrupt Service Routine (ISR). The user can re-enable interrupts in the interrupt service routine by writing to the appropriate bits in the Global Interrupt Enable Register. Interrupts can be nested to a level limited only by the available stack space. The Program Counter (PC) value and the Carry and Zero flags (CF, ZF) are automatically stored onto the Program Stack by the CALL instruction as part of the interrupt acknowledge Table 6-3. Interrupt Vector Assignments Interrupt Priority 0 (Highest) 1 2 3 4 5 6 7 (Lowest) 6.8.1 Interrupt Latency 0x00 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0E process. The user firmware is responsible for ensuring that the processor state is preserved and restored during an interrupt. For example the PUSH A instruction should be used as the first command in the ISR to save the accumulator value. And, the IPRET instruction should be used to exit the ISR with the accumulator value restored and interrupts enabled. The PC, CF, and ZF are restored when the IPRET or RET instructions are executed. The Interrupt Vectors supported by the USB Controller are listed in Table 6-3. Interrupt Vector 0 (Reset) has the highest priority, Interrupt Vector 7 has the lowest priority. Because the JMP instruction is two bytes long, the interrupt vectors occupy two bytes.
ROM Address Reset
Function 128-s timer interrupt 1.024-ms timer interrupt USB endpoint 0 interrupt USB endpoint 1 interrupt Reserved GPIO interrupt Wake-up interrupt
Interrupt latency can be calculated from the following equation: Interrupt Latency = (Number of clock cycles remaining in the current instruction) + (10 clock cycles for the CALL instruction) + (5 clock cycles for the JMP instruction)
For example, if a 5-clock-cycle instruction such as JC is being executed when an interrupt occurs, the first instruction of the Interrupt Service Routine executes a minimum of 16 clock cycles (1+10+5) or a maximum of 20 clock cycles (5+10+5) after the interrupt is issued. Therefore, the interrupt latency in this example will be = 20 clock periods = 20 / (12 MHz) = 1.667 s. The interrupt latches are sampled at the rising edge of the last clock cycle in the current instruction.
128-ms CLR Logic 1 128-ms Interrupt CLR D Q CLK 128-ms IRQ 1-ms CLR 1-ms IRQ End P0 CLR End P0 IRQ End P1 CLR End P1 IRQ GPIO CLR CLR CLR Interrupt Acknowledge Logic 1 GPIO Interrupt D CLK Wake-up CLR CLR Logic 1 CEXT D CLK Q Enable [7] Wake-up IRQ Interrupt Priority Encoder Q GPIO IRQ Enable [6]
Enable [1]
IRQ
Global Interrupt Enable Register
Enable [7:0]
Interrupt Vector
Figure 6-16. Interrupt Controller Logic Block Diagram Document #: 38-08026 Rev. *A Page 11 of 25
CY7C63001A CY7C63101A
6.8.2 GPIO Interrupt The General Purpose I/O interrupts are generated by signal transitions at the Port 0 and Port 1 I/O pins. GPIO interrupts are edge sensitive with programmable interrupt polarities. Setting a bit HIGH in the Port Pull-up Register (see Figure 611 and 6-12) selects a LOW to HIGH interrupt trigger for the corresponding port pin. Setting a bit LOW activates a HIGH to b7 IE0.7 W 0 b6 IE0.6 W 0 b5 IE0.5 W 0 b4 IE0.4 W 0 LOW interrupt trigger. Each GPIO interrupt is maskable on a per-pin basis by a dedicated bit in the Port Interrupt Enable Register. Writing a "1" enables the interrupt. Figure 6-17 and Figure 6-18 illustrate the format of the Port Interrupt Enable Registers for Port 0 and Port 1 located at I/O address 0x04 and 0x05 respectively. These write only registers are cleared during reset, thus disabling all GPIO interrupts. b3 IE0.3 W 0 b2 IE0.2 W 0 b1 IE0.1 W 0 b0 IE0.0 W 0
Figure 6-17. Port 0 Interrupt Enable Register (P0 IE - Address 0x04) b7 IE1.7 W 0 b6 IE1.6 W 0 b5 IE1.5 W 0 b4 IE1.4 W 0 b3 IE1.3 W 0 b2 IE1.2 W 0 b1 IE1.1 W 0 b0 IE1.0 W 0
Figure 6-18. Port 1 Interrupt Enable Register (P1 IE - Address 0x05) A block diagram of the GPIO interrupt logic is shown in Figure 6-19. The bit setting in the Port Pull-up Register selects the interrupt polarity. If the selected signal polarity is detected on the I/O pin, a HIGH signal is generated. If the Port Interrupt Enable bit for this pin is HIGH and no other port pins are requesting interrupts, the OR gate issues a LOW to HIGH
Port Pull-Up Register 1=LH 0=HAEL
signal to clock the GPIO interrupt flip-flop. The output of the flip-flop is further qualified by the Global GPIO Interrupt Enable bit before it is processed by the Interrupt Priority Encoder. Both the GPIO interrupt flip-flop and the Global GPIO Enable bit are cleared by on-chip hardware during GPIO interrupt acknowledge.
GPIO Interrupt Flip-Flop I D Q
OR Gate (1 input per GPIO pin)
GPIO Pin
M U X
CLR
1 = Enable 0 = Disable
Port Interrupt Enable Register
Interrupt Acknowledge
CLR
Global 1 = Enable GPIO Interrupt 0 = Disable Enable (Bit 6, Register 0x20)
Interrupt Priority Encoder
IRQ Interrupt Vector
Figure 6-19. GPIO Interrupt Logic Block Diagram Note. If one port pin triggers an interrupt, no other port pin can cause a GPIO interrupt until the port pin that triggered the interrupt has returned to its inactive (non-trigger) state or until its corresponding port interrupt enable bit is cleared (these events `reset' the clock of the GPIO Interrupt flip-flop, which must be `reset' to `0' before another GPIO interrupt event can `clock' the GPIO Interrupt flip-flop and produce an IRQ). Note. If the port pin that triggered an interrupt is held in its active (trigger) state while its corresponding port interrupt enable bit is cleared and then set, a GPIO interrupt event occurs as the GPIO Interrupt flip-flop clock transitions from `1' to `0' and then back to `1' (please refer to Figure 6-19). The USB Controller does not assign interrupt priority to different port pins and the Port Interrupt Enable Registers are not cleared during the interrupt acknowledge process. When a GPIO interrupt is serviced, the ISR must poll the ports to determine which pin caused the interrupt.
Document #: 38-08026 Rev. *A
Page 12 of 25
CY7C63001A CY7C63101A
6.8.3 USB Interrupt
6.9
USB Engine
A USB Endpoint 0 interrupt is generated after the host has written data to Endpoint 0 or after the USB Controller has transmitted a packet from Endpoint 0 and receives an ACK from the host. An OUT packet from the host which is NAKed by the USB Controller does not generate an interrupt. This interrupt is masked by the USB EP0 Interrupt Enable bit (bit 3) of the Global Interrupt Enable Register. A USB Endpoint 1 interrupt is generated after the USB Controller has transmitted a packet from Endpoint 1 and has received an ACK from the host. This interrupt is masked by the USB EP1 Interrupt Enable bit (bit 4) of the Global Interrupt Enable Register. 6.8.4 Timer Interrupt
The USB engine includes the Serial Interface Engine (SIE) and the low-speed USB I/O transceivers. The SIE block performs most of the USB interface functions with only minimal support from the microcontroller core. Two endpoints are supported. Endpoint 0 is used to receive and transmit control (including setup) packets while Endpoint 1 is only used to transmit data packets. The USB SIE processes USB bus activity at the transaction level independently. It does all the NRZI encoding/decoding and bit stuffing/unstuffing. It also determines token type, checks address and endpoint values, generates and checks CRC values, and controls the flow of data bytes between the bus and the Endpoint FIFOs. NOTE: the SIE stalls the CPU for three cycles per byte when writing data to the endpoint FIFOs (or 3 * 1/12 MHz * 8 bytes = 2 s per 8-byte transfer). The firmware handles higher level and function-specific tasks. During control transfers the firmware must interpret device requests and respond correctly. It also must coordinate Suspend/Resume, verify and select DATA toggle values, and perform function specific tasks. The USB engine and the firmware communicate though the Endpoint FIFOs, USB Endpoint interrupts, and the USB registers described in the sections below. 6.9.1 USB Enumeration Process
There are two timer interrupts: the 128-s interrupt and the 1.024-ms interrupt. They are masked by bits 1 and 2 of the Global Interrupt Enable Register respectively. The user should disable both timer interrupts before going into the suspend mode to avoid possible conflicts from timer interrupts occurring just as suspend mode is entered. 6.8.5 Wake-Up Interrupt
A wake-up interrupt is generated when the Cext pin goes HIGH. This interrupt is latched in the interrupt controller. It can be masked by the Wake-up Interrupt Enable bit (bit 7) of the Global Interrupt Enable Register. This interrupt can be used to perform periodic checks on attached peripherals when the USB Controller is placed in the low-power suspend mode. See the Instant-On Feature section for more details.
The USB Controller provides a USB Device Address Register at I/O location 0x12. Reading and writing this register is achieved via the IORD and IOWR instructions. The register contents are cleared during a reset, setting the USB address of the USB Controller to 0. Figure 6-20 shows the format of the USB Address Register. b3 ADR3 R/W 0 b2 ADR2 R/W 0 b1 ADR1 R/W 0 b0 ADR0 R/W 0
b7 Reserved 0
b6 ADR6 R/W 0
b5 ADR5 R/W 0
b4 ADR4 R/W 0
Figure 6-20. USB Device Address Register (USB DA - Address 0x12) Typical enumeration steps: 1. The host computer sends a SETUP packet followed by a DATA packet to USB address 0 requesting the Device descriptor. 2. The USB Controller decodes the request and retrieves its Device descriptor from the program memory space. 3. The host computer performs a control read sequence and the USB Controller responds by sending the Device descriptor over the USB bus. 4. After receiving the descriptor, the host computer sends a SETUP packet followed by a DATA packet to address 0 assigning a new USB address to the device. 5. The USB Controller stores the new address in its USB Device Address Register after the no-data control sequence completes. 6. The host sends a request for the Device descriptor using the new USB address. 7. The USB Controller decodes the request and retrieves the Device descriptor from the program memory. Document #: 38-08026 Rev. *A Page 13 of 25 8. The host performs a control read sequence and the USB Controller responds by sending its Device descriptor over the USB bus. 9. The host generates control reads to the USB Controller to request the Configuration and Report descriptors. 10.The USB Controller retrieves the descriptors from its program space and returns the data to the host over the USB. 11.Enumeration is complete after the host has received all the descriptors.
CY7C63001A CY7C63101A
6.9.2 Endpoint 0 6.9.2.1 Endpoint 0 Receive After receiving a packet and placing the data into the Endpoint 0 FIFO, the USB Controller updates the USB Endpoint 0 RX register to record the receive status and then generates a USB Endpoint 0 interrupt. The format of the Endpoint 0 RX Register is shown in Figure 6-21. All USB devices are required to have an endpoint number 0 that is used to initialize and manipulate the device. Endpoint 0 provides access to the device's configuration information and allows generic USB status and control accesses. Endpoint 0 can receive and transmit data. Both receive and transmit data share the same 8-byte Endpoint 0 FIFO located at data memory space 0x70 to 0x77. Received data may overwrite the data previously in the FIFO. b7 COUNT3 R/W 0 b6 COUNT2 R/W 0 b5 COUNT1 R/W 0 b4 COUNT0 R/W 0
b3 TOGGLE R 0
b2 IN R/W 0
b1 OUT R/W 0
b0 SETUP R/W 0
Figure 6-21. USB Endpoint 0 RX Register (Address 0x14) This is a read/write register located at I/O address 0x14. Any write to this register clears all bits except bit 3 which remains unchanged. All bits are cleared during reset. Bit 0 is set to 1 when a SETUP token for Endpoint 0 is received. Once set to a 1, this bit remains HIGH until it is cleared by an I/O write or a reset. While the data following a SETUP is being received by the USB engine, this bit is not cleared by an I/O write. User firmware writes to the USB FIFOs are disabled when bit 0 is set. This prevents SETUP data from being overwritten. Bits 1 and 2 are updated whenever a valid token is received on Endpoint 0. Bit 1 is set to 1 if an OUT token is received and cleared to 0 if any other token is received. Bit 2 is set to 1 if an IN token is received and cleared to 0 if any other token is received. Bit 3 shows the Data Toggle status of DATA packets received on Endpoint 0. This bit is updated for DATA following SETUP tokens and for DATA following OUT tokens if Stall (bit 5 of 0x10) is not set and either EnableOuts or StatusOuts (bits 3 and 4 of 0x13) are set. Bits 4 to 7 are the count of the number of bytes received in a DATA packet. The two CRC bytes are included in the count, so the count value is two greater than the number of data bytes received. The count is always updated and the data is always stored in the FIFO for DATA packets following a SETUP token. The count for DATA following an OUT token is updated if Stall (bit 5 of 0x10) is 0 and either EnableOuts or StatusOuts (bits 3 and 4 of 0x13) are 1. The DATA following an OUT is written into the FIFO if EnableOuts is set to 1 and Stall and StatusOuts are 0. A maximum of eight bytes are written into the Endpoint 0 FIFO. If there are less than eight bytes of data the CRC is written into the FIFO. Due to register space limitations, the Receive Data Invalid bit is located in the USB Endpoint 0 TX Configuration Register. Refer to the Endpoint 0 Transmit section for details. This bit is set by the SIE if an error is detected in a received DATA packet. Table 6-4 summarizes the USB Engine response to SETUP and OUT transactions on Endpoint 0. In the Data Packet column `Error' represents a packet with a CRC, PID or bitstuffing error, or a packet with more than eight bytes of data. `Valid' is a packet without an Error. `Status' is a packet that is a valid control read Status stage, while `N/Status' is not a correct Status stage (see section 6.9.4). The `Stall' bit is described in Section 6.9.2.2. The `StatusOuts' and `EnableOuts' bits are described in section 6.9.4.
Table 6-4. USB Engine Response to SETUP and OUT Transactions on Endpoint 0 Control Bit Settings Stall - - 0 0 0 0 1 1 0 0 0 Status Out Enable Out - - 0 0 0 0 0 0 1 1 1 - - 1 1 0 0 0 0 0 0 0 Received Packets Token Type SETUP SETUP OUT OUT OUT OUT OUT OUT OUT OUT OUT Data Packet Valid Error Valid Error Valid Error Valid Error Status N/Status Error FIFO Write Yes Yes Yes Yes No No No No No No No USB Engine Response Toggle Update Yes Yes Yes Yes No No No No Yes Yes Yes Count Update Yes Yes Yes Yes No No No No Yes Yes No Interrupt Yes Yes Yes Yes No No No No Yes Yes No Reply ACK None ACK None NAK None STALL None ACK STALL None
Document #: 38-08026 Rev. *A
Page 14 of 25
CY7C63001A CY7C63101A
6.9.2.2 Endpoint 0 Transmit The USB Endpoint 0 TX Register located at I/O address 0x10 controls data transmission from Endpoint 0 (see Figure 6-22). This is a read/write register. All bits are cleared during reset. b7 INEN R/W 0 b6 DATA1/0 R/W 0 b5 STALL R/W 0 b4 ERR R/W 0 b3 COUNT3 R/W 0 b2 COUNT2 R/W 0 b1 COUNT1 R/W 0 b0 COUNT0 R/W 0
Figure 6-22. USB Endpoint 0 TX Configuration Register (Address 0x10) Bits 0 to 3 indicate the numbers of data bytes to be transmitted during an IN packet, valid values are 0 to 8 inclusive. Bit 4 indicates that a received DATA packet error (CRC, PID, or bitstuffing error) occurred during a SETUP or OUT data phase. Setting the Stall bit (bit 5) stalls IN and OUT packets. This bit is cleared whenever a SETUP packet is received by Endpoint 0. Bit 6 (Data 1/0) must be set to 0 or 1 to select the DATA packet's toggle state (0 for DATA0, 1 for DATA1). After the transmit data has been loaded into the FIFO, bit 6 should be set according to the data toggle state and bit 7 set to "1". This enables the USB Controller to respond to an IN packet. Bit 7 is cleared and an Endpoint 0 interrupt is generated by the SIE once the host acknowledges the data transmission. Bit 7 is also cleared when a SETUP token is b7 INEN R/W 0 b6 DATA1/0 R/W 0 b5 STALL R/W 0 b4 EP1EN R/W 0 received. The Interrupt Service Routine can check bit 7 to confirm that the data transfer was successful. 6.9.3 Endpoint 1
Endpoint 1 is capable of transmit only. The data to be transmitted is stored in the 8-byte Endpoint 1 FIFO located at data memory space 0x78 to 0x7F. 6.9.3.1 Endpoint 1 Transmit Transmission is controlled by the USB Endpoint 1 TX Register located at I/O address 0x11 (see Figure 6-23). This is a read/write register. All bits are cleared during reset.
b3 COUNT3 R/W 0
b2 COUNT2 R/W 0
b1 COUNT1 R/W 0
b0 COUNT0 R/W 0
Figure 6-23. USB Endpoint 1 TX Configuration Register (Address 0x11) Bits 0 to 3 indicate the numbers of data bytes to be transmitted during an IN packet, valid values are 0 to 8 inclusive. Bit 4 must be set before Endpoint 1 can be used. If this bit is cleared, the USB Controller ignores all traffic to Endpoint 1. Setting the Stall bit (bit 5) stalls IN and OUT packets until this bit is cleared. Bit 6 (Data 1/0) must be set to either 0 or 1 depending on the data packet's toggle state, 0 for DATA0, 1 for DATA1. After the transmit data has been loaded into the FIFO, bit 6 should be set according to the data toggle state and bit 7 set b7 Reserved 0 b6 Reserved 0 b5 Reserved 0 b4 ENOUTS R/W 0 to "1". This enables the USB Controller to respond to an IN packet. Bit 7 is cleared and an Endpoint 1 interrupt is generated by the SIE once the host acknowledges the data transmission. 6.9.4 USB Status and Control
USB status and control is regulated by USB Status and Control Register located at I/O address 0x13 as shown in Figure 6-24. This is a read/write register. All reserved bits must be written to zero. All bits in the register are cleared during reset. b3 STATOUTS R/W 0 0 b2 FORCEJ b1 FORCEK R/W 0 b0 BUSACT R/W 0
Figure 6-24. USB Status and Control Register (USB SCR - Address 0x13) Bit 0 is set by the SIE if any USB activity except idle (D+ LOW, D- HIGH) is detected. The user program should check and clear this bit periodically to detect any loss of bus activity. Writing a 0 to this bit clears it. Writing a 1 does not change its value. Bit 1 is used to force the on-chip USB transmitter to the K state which sends a Resume signal to the host. Bit 2 is used to force the transmitter to the J state. This bit should normally be set to Document #: 38-08026 Rev. *A zero. However, for resume signaling, force a J state for one instruction before forcing resume. Bit 3 is used to automatically respond to the Status stage OUT of a control read transfer on Endpoint 0. A valid Status stage OUT contains a DATA1 packet with 0 bytes of data. If the StatusOuts bit is set, the USB engine responds to a valid Status stage OUT with an ACK, and any other OUT with a STALL.
Page 15 of 25
CY7C63001A CY7C63101A
The data is not written into the FIFO when this bit is set. This bit is cleared when a SETUP token is received by Endpoint 0. Bit 4 is used to enable the receiving of Endpoint 0 OUT packets. When this bit is set to 1, the data from an OUT transaction is written into the Endpoint 0 FIFO. If this bit is 0, data is not written to the FIFO and the SIE responds with a NAK. This bit is cleared following a SETUP or ACKed OUT transaction. Note. After firmware decodes a SETUP packet and prepares for a subsequent OUT transaction by setting bit 4, bit 4 is not cleared until the hand-shake phase of an ACKed OUT transaction (a NAKed OUT transaction does not clear this bit). 6.10.1 Low-Speed Driver Characteristics The CY7C630/101A devices use a differential output driver to drive the Low-speed USB data signal onto the USB cable, as shown in Figure 6-25. The output swings between the differential HIGH and LOW state are well balanced to minimize signal skew. Slew rate control on the driver minimizes the radiated noise and cross talk on the USB cable. The driver's outputs support three-state operation to achieve bidirectional half duplex operation. The CY7C630/101A driver tolerates a voltage on the signal pins of -0.5V to 3.8V with respect to local ground reference without damage. The driver tolerates this voltage for 10.0 s while the driver is active and driving, and tolerates this condition indefinitely when the driver is in its highimpedance state. A low-speed USB connection is made through an unshielded, untwisted wire cable a maximum of three meters in length. The rise and fall time of the signals on this cable are well controlled to reduce RFI emissions while limiting delays, signaling skews and distortions. The CY7C630/101A driver reaches the specified static signal levels with smooth rise and fall times, resulting in minimal reflections and ringing when driving the USB cable. This cable and driver are intended to be used only on network segments between low-speed devices and the ports to which they are connected.
6.10
USB Physical Layer Characteristics
The following section describes the CY7C630/101A compliance to the Chapter 7 Electrical section of the USB Specification, Revision 1.1. The section contains all signaling, power distribution, and physical layer specifications necessary to describe a low- speed USB function.
One Bit Time (1.5Mb/s)
VSE (max) Driver Signal Pins VSE (min) VSS
Signal pins pass output spec levels with minimal reflections and ringing
Figure 6-25. Low-speed Driver Signal Waveforms 6.10.2 Receiver Characteristics the differential data lines are outside the common mode range, as shown in Figure 6-26. The receiver tolerates static input voltages between -0.5V and 3.8V with respect to its local ground reference without damage. In addition to the differential receiver, there is a single-ended receiver for each of the two data lines. The single-ended receivers have a switching threshold between 0.8V and 2.0V (TTL inputs).
The CY7C630/101A has a differential input receiver which is able to accept the USB data signal. The receiver features an input sensitivity of at least 200 mV when both differential data inputs are in the range of at least 0.8V to 2.5V with respect to its local ground reference. This is the common mode input voltage range. Proper data reception is also guaranteed when
Document #: 38-08026 Rev. *A
Page 16 of 25
CY7C63001A CY7C63101A
Minimum Differential Sensitivity (volts)
1.0
0.8
0.6
0.4
0.2
0.0 0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
Common Mode Input Voltage (volts)
Figure 6-26. Differential Input Sensitivity Over Entire Common Mode Range
6.11
External USB Pull-Up Resistor
The USB system specifies that a pull-up resistor be connected on the D- pin of low-speed peripherals as shown in Figure 627. To meet the USB 1.1 spec (section 7.1.6), which states that the termination must charge the D- line from 0 to 2.0 V in 2.5 s, the total load capacitance on the D+/D- lines of the low-speed USB device (Cypress device capacitance + PCB
Port0 Port0
trace capacitance + integrated cable capacitance) must be less than 250 pF. As Cypress D+/D- transceiver input capacitance is 20pF max, up to 230 pF of capacitance is allowed for in the low speed device's integrated cable and PCB. If the cable + PCB capacitance on the D+/D- lines will be greater than approximately 230 pF, an external 3.3V regulator must be used as shown in Figure 6-28.
Switches, Devices, Etc.
Switches, Devices, Etc.
7.5kW1% +4.35V (min)
For Cext Wake-up Mode
6-MHz Resonator
0.1F
4.7 F
Figure 6-27. Application Showing 7.5kW 1% Pull-Up Resistor
+3.3V Switches, Devices, Etc.
Port0 Port0
3.3V Reg
Switches, Devices, Etc.
0.1 F
+4.35V (min.) For Cext Wake-up Mode 6-MHz Resonator 0.1F 4.7 F
Figure 6-28. Application Showing 1.5-kW 5% Pull-Up Resistor
Document #: 38-08026 Rev. *A
USB Connector
Port1 VSS VPP CEXT XTALIN
Port1 D+ D- VCC XTALOUT
1.5kW
USB Connector
Port1 VSS VPP CEXT XTALIN
Port1 D+ D- VCC XTALOUT
Page 17 of 25
CY7C63001A CY7C63101A
6.12 Instruction Set Summary
MNEMONIC HALT ADD A,expr ADD A,[expr] ADD A,[X+expr] ADC A,expr ADC A,[expr] ADC A,[X+expr] SUB A,expr SUB A,[expr] SUB A,[X+expr] SBB A,expr SBB A,[expr] SBB A,[X+expr] OR A,expr OR A,[expr] OR A,[X+expr] AND A,expr AND A,[expr] AND A,[X+expr] XOR A,expr XOR A,[expr] XOR A,[X+expr] CMP A,expr CMP A,[expr] CMP A,[X+expr] MOV A,expr MOV A,[expr] MOV A,[X+expr] MOV X,expr MOV X,[expr] IPRET XPAGE data direct index data direct index data direct index data direct index data direct index data direct index data direct index data direct index data direct index data direct addr operand opcode 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D OE 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 4 6 7 4 6 7 4 6 7 4 6 7 4 6 7 4 6 7 4 6 7 5 7 8 4 5 6 4 5 13 4 cycles 7 NOP INC A INC X INC [expr] INC [X+expr] DEC A DEC X DEC [expr] DEC [X+expr] IORD expr IOWR expr POP A POP X PUSH A PUSH X SWAP A,X SWAP A,DSP MOV [expr],A MOV [X+expr],A OR [expr],A OR [X+expr],A AND [expr],A AND [X+expr],A XOR [expr],A XOR [X+expr],A IOWX [X+expr] CPL ASL ASR RLC RRC RET direct index direct index direct index direct index index acc x direct index acc x direct index address address MNEMONIC operand opcode 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 4 4 4 7 8 4 4 7 8 5 5 4 4 5 5 5 5 5 6 7 8 7 8 7 8 6 4 4 4 4 4 8 cycles
Table 6-5. Instruction Set Map
JMP CALL JZ JNZ
addr addr addr addr
8x 9x Ax Bx
5 10 5 5
JC JNC JACC INDEX
addr addr addr addr
Cx Dx Ex Fx
5 5 7 14
Document #: 38-08026 Rev. *A
Page 18 of 25
CY7C63001A CY7C63101A
7.0 Absolute Maximum Ratings
DC Voltage Applied to Outputs in High-Z state ......................................... -0.5V to +VCC+0.5V Max. Output Current into Port 1 Pins .......................... 60 mA Max. Output Current into Non-Port 1 Pins.................. 10 mA Power Dissipation..................................................... 300 mW Static Discharge Voltage .......................................... > 2000V Latch-up Current[1] ................................................ > 200 mA
Storage Temperature ................................. -65C to +150C Ambient Temperature with Power Applied ...... -0C to +70C Supply Voltage on VCC Relative to VSS ......... -0.5V to +7.0V DC Input Voltage................................... -0.5V to +VCC+0.5V
8.0
Electrical Characteristics fOSC = 6 MHz; Operating Temperature = 0 to 70C, VCC = 4.0 to 5.25V
Description General VCC Operating Supply Current Supply Current--Suspend Mode Supply Current--Start-up Mode Programming Voltage (disabled) Resonator Start-up Interval Watchdog Timer Period Power On Reset VCC Slew USB Interface Static Output High Static Output Low Differential Input Sensitivity Differential Input Common Mode Range Single Ended Receiver Threshold Transceiver Input Capacitance Data Line (D+, D-) Leakage External Bus Pull-up Resistance, D- pin External Bus Pull-up Resistance, D- pin External Bus Pull-down Resistance General Purpose I/O Interface Pull-up Resistance Port 0 Sink Current (0), lowest current Port 0 Sink Current (F), highest current Port 1 Sink Current (0), lowest current Port 1 Sink Current (F), highest current Sink Current max./min. Differential Nonlinearity Tracking Ratio Port1 to Port0 Current Sink Response Time Port 1 Max Sink Current Vout = 2.0V DC, Port 0 only[5]
[5]
Parameter ICC ISB1 ISB2 VPP tstart twatch tVCCS Voh Vol Vdi Vcm Vse Cin Ilo Rpu1 Rpu2 Rpd Rup Isink0(0) Isink0(F) Isink1(0) Isink1(F) Irange Ilin Tratio tsink Imax
Conditions
Min.
Max. 25
Unit mA A mA V s ms ms V V V V V pF A k k k k mA mA mA mA mA lSB s mA
Resonator off, D- > Voh min
[2]
20 4 -0.4 0.4 256 7.168 8.192 1000 3.6 0.3 0.2 0.8 0.8 2.5 2.0 20 -10 1.425 7.425 14.25 8 0.1 0.5 1.6 8 5 4.5 14.4 10 1.575 7.575 15.75 24 0.3 1.5 4.8 24 5.5 0.5 19.6 0.8 60
Ceramic resonator
Linear ramp on VCC pin to VCC[3, 4] 15k 5% to Gnd[5,6] See Notes 5 and 6 |(D+)-(D-)|, and Figure 6-26 Figure 6-26 D+ to Vss; D- to Vss 0 V <(D+, D-)<3.3 V, Hi-Z State 1.5 k 5% to 3.3V supply 7.5 k 1% to 15 k 5% Vcc[7]
0.010 2.8
Vout = 2.0V DC, Port 0 only[5] Vout = 2.0V DC, Port 1 only Vout = 2.0V DC, Port 1 only[5] Vout = 0.4V DC, Port 1 only[5] Vout = 2.0V DC, Port 0 or 1[5, 8] Port 0 or Port 1[11] Vout = 2.0V[12] Full scale transition Summed over all Port 1 bits
Notes: 1. All pins specified for >200 mA positive and negative injection, except P1.0 is specified for >50 mA negative injection. 2. Cext at VCC or Gnd, Port 0 and Port1 at VCC. 3. Part powers up in suspend mode, able to be reset by USB Bus Reset. 4. POR may re-occur whenever VCC drops to approximately 2.5V. 5. Level guaranteed for range of VCC = 4.35V to 5.25V. 6. With Rpu1 of 1.5 KW5% on D- to 3.3V regulator. 7. Maximum matched capacitive loading allowed on D+ and D- (including USB cable and host/hub) is approximately 230 pF. 8. Irange = Isink(F)/Isink(0 ) for each port 0 or 1 output.
Document #: 38-08026 Rev. *A
Page 19 of 25
CY7C63001A CY7C63101A
8.0
Pmax Vith VH VHCext Iin IinCx ICext Vol1 Vol2
Electrical Characteristics fOSC = 6 MHz; Operating Temperature = 0 to 70C, VCC = 4.0 to 5.25V (continued)
Description Port 1 & Cext Sink Mode Dissipation Input Threshold Voltage Input Hysteresis Voltage Input Hysteresis Voltage, Cext Input Leakage Current, GPIO Pins Input Leakage Current, Cext Pin Sink Current, Cext Pin Output LOW Voltage, Cext Pin Output LOW Voltage, Cext Pin Per pin All ports and Cext[13] Port 0 and Port 1[14] Cext Pin Only[14] Port 0 and Port 1, Vout = 0 or VCC VCext = 0 or VCC VCext = VCC VCC = Min., Iol = 2 mA VCC = Min., Iol = 5 mA 6
[15]
Parameter
Conditions
Min. 45% 6% 12% -1
Max. 25 65% 12% 30% 1 50 18 0.4 2.0
Unit mW VCC VCC VCC A nA mA V V
9.0
Switching Characteristics
Description Clock Input Clock Cycle Time Clock HIGH Time Clock LOW Time USB Driver Characteristics USB Data Transition Rise Time USB Data Transition Fall Time Rise/Fall Time Matching Output Signal Crossover Voltage USB Data Timing Low Speed Data Rate Receiver Data Jitter Tolerance Receiver Data Jitter Tolerance EOP Width at Receiver Width of SE0 Interval During Differential Transition Source EOP Width Differential Driver Jitter Differential Driver Jitter To next transition, Figure 9-5 To paired transition, Figure 9-5 1.25 -95 -150 See Notes 5, 6, and 9 See Notes 5, 6, and 9 tr/tf See Note 5 Ave. Bit Rate (1.5 Mb/s 1.5%) To Next Transition, Figure 9-4[10] 9-3[10] For Paired Transitions, Figure 9-3[10] Accepts as EOP[10] Conditions Min. 166.67 0.45 tCYC 0.45 tCYC 75 75 80 1.3 1.4775 -75 -45 -40 670 210 1.50 95 150 300 300 125 2.0 1.5225 75 45 100 Max. 166.67 Unit ns ns ns ns ns % V Mb/s ns ns ns ns ns s ns ns
Parameter tCYC tCH tCL tr tf trfm Vcrs tdrate tdjr1 tdjr2 tdeop teopr tlst teopt tudj1 tudj2
Differential to EOP Transition Skew Figure
Notes: 9. Cload of 200 (75 ns) to 600 pF (300 ns). 10. Measured at crossover point of differential data signals. 11. Measured as largest step size vs. nominal according to measured full scale and zero programmed values 12. Tratio = Isink1(n)/Isink0(n) for the same n. 13. Low to High transition. 14. This parameter is guaranteed, but not tested. 15. With Ports configured in Hi-Z mode.
Document #: 38-08026 Rev. *A
Page 20 of 25
CY7C63001A CY7C63101A
tCYC tCH
CLOCK
tCL Figure 9-1. Clock Timing
Voh Vcrs Vol
D+
tr
90% 10% 90%
tf
10%
D-
Figure 9-2. USB Data Signal Timing and Voltage Levels
TPERIOD Differential Data Lines
TJR TJR1 TJR2
Consecutive Transitions N * TPERIOD + TJR1 Paired Transitions N * TPERIOD + TJR2
Figure 9-3. Receiver Jitter Tolerance
TPERIOD Differential Data Lines
Crossover Point
Crossover Point Extended
Diff. Data to SE0 Skew N * TPERIOD + TDEOP
Source EOP Width:
TEOPT
Receiver EOP Width: TEOPR1, TEOPR2
Figure 9-4. Differential to EOP Transition Skew and EOP Width
Document #: 38-08026 Rev. *A
Page 21 of 25
CY7C63001A CY7C63101A
TPERIOD Differential Data Lines
Crossover Points
Consecutive Transitions N * TPERIOD + TxJR1 Paired Transitions N * TPERIOD + TxJR2
Figure 9-5. Differential Data Jitter
10.0
Ordering Information
EPROM Size 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB Number of GPIO 12 12 12 12 16 16 16 16 Package Name P5 P5 S5 S5 Q13 Q13 - - Package Type 20-Pin (300-Mil) PDIP 20-Pin (300-Mil) PDIP Lead-free 20-Pin (300-Mil) SOIC 20-Pin (300-Mil) SOIC Lead-free 24-Pin (150-Mil) QSOP 24-Pin (150-Mil) QSOP Lead-free DIE Form DIE Form Lead-free Operating Range Commercial Commercial Commercial Commercial Commercial Commercial Commercial Commercial
Ordering Code CY7C63001A-PC CY7C63001A-PXC CY7C63001A-SC CY7C63001A-SXC CY7C63101A-QC CY7C63101A-QXC CY7C63001A-XC CY7C63001A-XWC
11.0
Package Diagrams
20-Lead (300-Mil) Molded DIP P5
51-85011-*A
Document #: 38-08026 Rev. *A
Page 22 of 25
CY7C63001A CY7C63101A
11.0 Package Diagrams (continued)
24-Lead Quarter Size Outline Q13
51-85055-*B
20-Lead (300-Mil) Molded SOIC S5
51-85024-*B
Document #: 38-08026 Rev. *A
Page 23 of 25
CY7C63001A CY7C63101A
11.0 Package Diagrams (continued)
51-85025-*B
DIE FORM
4 3 2 1 24 23 22 21 5 6 7 8 Y 20 19 18 17
9 10 11 12 13 14 15 16 (0,0) X
Table 11-1 below shows the die pad coordinates for the CY7C63001A-XC and CY7C63001A-XWC. The center location of each bond pad is relative to the bottom left corner of the die which has coordinate (0,0). Table 11-1. CY7C63001A-XC Probe Pad Coordinates in Microns ((0,0) to Bond Pad Centers) Pad # 1 2 3 4 5 6 7 8 9 10 11 12 Pin Name Port00 Port01 Port02 Port03 Port10 Port12 Port14 Port16 Vss Vpp Cext Xtalin X (microns) 676.00 507.35 338.70 170.05 120.10 120.10 120.10 120.10 148.50 278.30 414.25 653.45 Y (microns) 2325.40 2325.40 2325.40 2325.40 2132.30 1962.90 1765.20 1595.80 121.80 121.80 121.80 121.80 Pad # 13 14 15 16 17 18 19 20 21 22 23 24 Pin Name Xtlout Vcc DD+ Port17 Port15 Port13 Port11 Port07 Port06 Port05 Port04 X (microns) 794.85 1033.55 1129.75 1451.70 1446.10 1446.10 1446.10 1446.10 1395.65 1227.00 1058.35 889.7 Y (microns) 121.80 121.80 121.80 121.80 1595.80 1765.20 1962.90 2132.30 2325.40 2325.40 2325.40 2325.40
All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-08026 Rev. *A
Page 24 of 25
(c) Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C63001A CY7C63101A
Document History Page
Document Title: CY7C63001A, CY7C63101A Universal Serial Bus Microcontroller Document Number: 38-08026 REV. ** *A ECN NO. 116223 276070 Issue Date 06/12/02 See ECN Orig. of Change DSG BON Description of Change Change from Spec number: 38-00662 to 38-08026 Added die form and bond pad information. Added lead-free packages. Removed obsolete packages and their references.
Document #: 38-08026 Rev. *A
Page 25 of 25

▲Up To Search▲

Price & Availability of CY7C63101A-QXC

	To Download CY7C63101A-QXC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .